On-Demand Tokencodes

Document created by RSA Information Design and Development on Jun 13, 2017Last modified by RSA Information Design and Development on Jun 13, 2017
Version 2Show Document
  • View in full screen mode

The following table lists the MIB objects available for on-demand tokencodes.

                                                                                             

MIB Object

OID

Description

amOttTokencodeReqsTotal

.1.3.6.1.4.1.2197.30.8.1

Total number of on-demand tokencode requests.

amOttAuthReqsTotal

.1.3.6.1.4.1.2197.30.8.2

Total number of authentication requests using on-demand tokencodes.

amOttSmsProvider

.1.3.6.1.4.1.2197.30.8.3

Name of the SMS provider the deployment is configured to use.

amOttMsgsSmsTotal

.1.3.6.1.4.1.2197.30.8.4

Total number of on-demand tokencode messages using SMS for transport.

amOttMsgsSmsPerSec

.1.3.6.1.4.1.2197.30.8.5

Average on-demand tokencode messages using SMS for transport.

amOttMsgsSmtpTotal

.1.3.6.1.4.1.2197.30.8.6

Total number of on-demand tokencode messages using SMTP for transport.

amOttMsgsSmtpPerSec

.1.3.6.1.4.1.2197.30.8.7

Average on-demand tokencode messages using SMTP for transport.

amOttMsgsSmtpGatewayPercent

.1.3.6.1.4.1.2197.30.8.8

This value is for use by RSA. It is intended for diagnostic and troubleshooting purposes only.

Estimated percentage of SMTP messages sent to what appears to be an SMTP-to-SMS gateway. If the part of the e-mail address before the at sign (@) is only digits, it is assumed to be an SMTP-to-SMS gateway.

amOttAuthAttemptsPerSec

.1.3.6.1.4.1.2197.30.8.9

This value is for use by RSA. It is intended for diagnostic and troubleshooting purposes only.

Average number of authentication requests per second.

amOttAuthAttemptsSecurIDPercent

.1.3.6.1.4.1.2197.30.8.10

This value is for use by RSA. It is intended for diagnostic and troubleshooting purposes only.

Percentage of authentication requests that are dispatched back to the SecurID authentication method. These are cases where the user is enabled for both SecurID and on-demand authentication (ODA) and the tokencode fails ODA.

amOttAuthAttemptsLegacyPercent

.1.3.6.1.4.1.2197.30.8.11

This value is for use by RSA. It is intended for diagnostic and troubleshooting purposes only.

Percentage of authentication requests originating from legacy agents.

amOttPinSetSytemTotal

.1.3.6.1.4.1.2197.30.8.12

This value is for use by RSA. It is intended for diagnostic and troubleshooting purposes only.

Total number of PINs automatically generated after enablement.

amOttPinSetDeferredTotal

.1.3.6.1.4.1.2197.30.8.13

This value is for use by RSA. It is intended for diagnostic and troubleshooting purposes only.

Total number of PINs set by the user after enablement.

amOttPinSetTemporaryTotal

.1.3.6.1.4.1.2197.30.8.14

This value is for use by RSA. It is intended for diagnostic and troubleshooting purposes only.

Total number of PINs set temporarily during enablement.

amOttPinSetPermanentTotal

.1.3.6.1.4.1.2197.30.8.15

This value is for use by RSA. It is intended for diagnostic and troubleshooting purposes only.

Total number of PINs set permanently during enablement.

amOttRateSampleTimeS

.1.3.6.1.4.1.2197.30.8.16

Interval over which all rate-based values are sampled, in seconds.

 

 

 

 


Attachments

    Outcomes