on Oct 13, 2008Hi, any people try to log SAP?? is it working?
This SAP logs doesn´t parsing
The SAP log is collected like "unknown" device
Thanks a lot for all comments about!
Allan
Hi David, thanks for you support
I can`t to log SAP device
I`m attached the SAP log, this file is ok, but we have SAP in spanish (see log)
I have open a case Support Incident C0882542 with Stef.Belyea@rsa.com but at moment, We haven`t answer
We need a solution for this issue, We are working with SOX and We need to log SAP
Dou you have any example of SAP log for testing my enVision?
Please, if you can, help me with this problem, is very important..
Thanks a lot!!!
Allan Hougham
Hi Allan,
Unfortunately I do not. I have asked other customers and engineers about their SAP setups (since I do not have customers with a SAP configuration), and all have suggested that the configuration guide steps worked for them.
I suggest that you continue to press the support team for an answer, and if necessary engage your local envision specialist and technical consultant to assist you in driving this issue to a resolution. Escalate the case according to your maintenance agreement until you have a working solution, keeping in mind that a support case is a two way street and they will need your assistance in working together towards a solution.
What has been the progress (if any) with the support case? Have they suggested anything useful, and can you share the results of any recommendations they gave you?
Kind Regards,
dm
Hi David,
Thanks for you support, I have a ticket support opened at october 8, but I dont have news for this problem.
On this moment I maked a script, my script make a translation of the SAP log, the fields in spanish are replaced for fields in english, then it´s work fine! is this a solution in house, but is any.
The envision support is working with this problem, but I don´t have time... and I don´t have news of envision support. I think that envision support is very bad
I´m system engineer of envision and I known fine the appliance, it´s case is only modify the code ZRSA_ with a ABAP programer, to foce this code to english, no more.
Thanks a lot for you suggest
Allan
Hi,
enVision SAP support is documented on Secure Care Online (https://knowledge.rsasecurity.com/scolcms/set.aspx?id=182) We do not suppport any deviations from this config documents.
Looking at the discussion, it also appears that there is a need for Non English Characters. enVision is currently not rated for receiving non english ie double byte / UTF-8 characters. We are planning a potential internationalized enVison somewher mid CY09 (to be confirmed later).
Additionally, enVision IC is not the place to discuss individual support tickets. If our communication works fine the customer will be updated on this issue via various other channels.
Last, if there is a need to request a Spanish Version of SAP please look at this post [[page no longer exists]]
Appologies if thus message is maybe to harsh . Clearity and setting the rigth expectations will benefit everyone are in the long term.
Hi,
I have issue in integrating SAP ECC 6.0 with RSA enVision. Can somebody let me know the procedure for the same. As the configuration document provided by RSA is for SAP version 4.7. I am stucking at the TASK III of the configuration document. It says the JOB ZRSA is unknown. Pls help me with issue.
Thanks & regards,
Sandeep Jain
Ya Sure Allan,
It would be great if you can help me out.
Regards,
Sandeep
ok, we have sap 4.3, you too?
is you sap in english, spanish, german?? what lenguage?
What version of enVision have you?
Thanks!
Allan
Dear Allan,
We have SAP ECC 6.0. We have SAP in english. And we have Envision version 4.0.
Regards,
Sandeep
Hi, you have SAP ECC 6.0. recently? before you had SAP 4.3??
Reg
Allan
No we have SAP ECC Version 6.0 only.
Regards,
Sandeep
ok, if you see in RSA documentation is Supported SAP Versions 4.7 ONLY:
https://knowledge.rsasecurity.com/docs/rsa_env/device_config/SAP_R3_Enterprise.pdf
You can try this configuration for SAP 6.0 but I don´t know if this work fine.
Try you this configuration before? Can you send me any print screen?
Reg
Allan
Ya I have tried the configuration document. But we have struck at the Task III mentioned in the document ie. to execute the ZRSA Script. We need to change the Script I suppose. But it needs ABAP Programmer I suppose.
I cant send you the Print Screen as The servers are not maintained by as. Our SAP team will maintain the servers.
Regards,
Sandeep
Sandeep, you can try with this ZRSA Script, this is modificated beacause didn´t work fine
I attached
Allan
Thanks Allan,
Will Try and let you know whether we are successful or not.
Regards,
Sandeep
Hi.
We are going to implement RSA via L&G but SAP connector is not very clear.
has somebody experience on Connect RSA to SAP central user Administration
Hi Allan!
SAP is working at other customers. Can you post some details about the steps that you followed to get it configured and any errors that you received?
I would definitely also open a support case at the same time - if I notice anything obvious I can comment, but it may be something that requires support input.
Kind Regards,
David